R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
P4500
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Poulan
1030 Stevens Creek Road
Augusta, GA 30907
Poulan
5855 Terry Fox Way
Mississauga, Ontario L5V 3E4
545154719 Rev. 1 11/01/07 BRW
IDENTIFICATION OF SAFETY SYMBOLS
Store unit indoors in a high, dry place out of the reach of
children.
When servicing unit, use only identical replace-
ment parts.
Always stop unit and disconnect spark plug before
cleaning or servicing.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
Use unleaded gasoline and two--stroke oil mixed at a ratio of
40:1 (2.5%).
SAFETY RULES
WARNING: When using gardening
appliances, basic safety precautions must al-
ways be followed to reduce the risk of fire and
serious injury. Read and follow all instructions.
This power unit can be dangerous! Operator is
responsible for following instructions and warn-
ings on unit and in manual. Read entire instruc-
tion manual before using unit! Be thoroughly fa-
miliar with the controls and the proper use of the
unit. Restrict the use of this unit to persons who
have read, understand, and will follow the
instructions and warnings on the unit and in the
manual. Never allow children to operate this
unit.
WARNING: Trimmer line throws ob-
jects violently. You and others can be blinded/in-
jured. Wear eye and leg protection. Keep body
parts clear of rotating line.
Eye Protection
HazardZone
50 ft.
INSTRUCTION
MANUAL
(15 m)
Boots
Keep children, bystanders, and animals 50 feet
(15 meters) away. Stop unit immediately if ap-
proached.
If situations occur which are not covered in
this manual, use care and good judgment. If
youneed assistance, contact your authorized
service dealer or call 1--800--554--6723.
SAFETY INFORMATION ON THE UNIT
DANGER: Never use blades or flail-
ing devices. This unit is designedfor line trim-
mer use only. Use of any other accessories or
attachments will increase the risk of injury.
3
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before re-
moving fuel cap.
OPERATOR SAFETY
S Dress properly.
Always wear safety
glasses or similar eye protection when op-
erating, or performing maintenance, on
your unit (safety glasses are available).
Eye protection should be marked Z87.
S Always wear face or dust mask if operation
is dusty.
S Always wear heavy, long pants, long sleeves,
boots, and gloves. Wearing safety leg guards
is recommended.
S Always wear foot protection. Do not go
barefoot or wear sandals. Stay clear of
spinning line.
S Secure hair above shoulder length. Secure
or remove loose clothing or clothing with
loosely hanging ties, straps, tassels, etc.
They can be caught in moving parts.
S Being fully covered also helps protect you
from debris and pieces of toxic plants
thrown by spinning line.
S Always store gasoline in a container ap-
proved for flammable liquids.
CUTTING SAFETY
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your left to your right. Cutting on
right side of the shield will throw debris away
from the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool before storing or trans-
porting in vehicle.
S Stay alert. Do not operate this unit when you
are tired, ill, upset or under the influence of al-
cohol, drugs, or medication. Watch what you
are doing; use common sense.
S Wear hearing protection.
S Never start or run inside a closed room or
building. Breathing exhaust fumes can kill.
S Keep handles free of oil and fuel.
UNIT / MAINTENANCE SAFETY
S Disconnect the spark plug before perform-
ing maintenance except carburetor adjust-
ments.
S Look for and replace damaged or loose
parts before each use. Look for and repair
fuel leaks before use. Keepin good working
condition.
S Replace trimmer head parts that are
chipped, cracked, broken, or damaged in
any other way before using the unit.
S Maintain unit according to recommended pro-
cedures. Keep cutting line at proper length.
S Use only 0.080 inch (2 mm) diameter Poulan/
WEED EATER brand replacement line. Nev-
er use wire, rope, string, etc.
S Empty the fuel tank before storing or trans-
porting the unit. Use upfuel left in the carbu-
retor by starting the engine and letting it run
until it stops.
S Store unit andfuelin area where fuelvapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
S Store unit so line limiter blade cannot acci-
dentally cause injury. The unit can be hung
by the shaft.
S Store unit out of reach of children.
WARNING: The engine exhaust
from this product contains chemicals known
totheState of California to cause cancer, birth
defects or other reproductive harm.
S Install required shield properly before using
the unit. Use only specified trimmer head;
make sure it is properly installed and securely
fastened.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people. If symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti--vibration system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool.
S Make sure unit is assembled correctly as
shown in this manual.
S Make carburetor adjustments with lower
end supported to prevent line from contact-
ing any object.
S Keep others away when making carburetor
adjustments.
S Use only recommended Poulan/WEED
EATER accessories and replacement parts.
S Have all maintenance and service not ex-
plained in this manual performed by an au-
thorized service dealer.
FUEL SAFETY
S Mix and pour fuel outdoors.
S Keep away from sparks or flames.
S Use a container approved for fuel.
S Do not smoke or allow smoking near fuel or
the unit.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark ar-
resting screen which meets the requirements of
California Codes 4442 and 4443. All U.S. forest
land and the states of California, Idaho, Maine,
S Avoid spilling fuel or oil. Wipe up all fuel
spills.
4
Minnesota, New Jersey, Oregon, and Washing-
ton require by law that many internal combus-
tion engines be equipped with a spark arresting
screen. If you operate in a locale where such
regulations exist, you are legally responsible for
maintaining the operating condition of these
parts. Failure to do so is a violation of the law.
For normal homeowner use, the muffler and
spark arresting screen will not require any ser-
vice. After 50 hours of use, we recommend that
your muffler be serviced or replaced by an au-
thorized service dealer.
ASSEMBLY
ATTACHING SHIELD
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion to the operator and others from the risk of
thrown objects, and is equipped with a line limit-
er blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ADJUSTING THE HANDLE
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shielduntil bolt passes through hole
in bracket.
4. Securely tighten wing nut onto bolt.
WARNING: When adjusting the assist
handle, be sure it remains above the safety label
and below the mark or arrow on the shaft.
1. Loosen wing nut on handle.
2. Rotate the handle on the shaft to an upright
position; retighten wing nut.
Wing Nut
Bracket
x
PIVOT
5
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Muffler
Assist Handle
Trimmer
Head
Shaft
Safety Label
Shaft Mark or Arrow
Shield
Spark Plug
Primer Bulb
Throttle Trigger
Fuel Mix Fill Cap
Line Limiter Blade
STOP
Switch
Choke Lever
Starter Handle
STOP SWITCH
CHOKE
The STOP switch is used to stop the engine. To
stop the engine, push and hold the switch in the
STOP position until the engine stops.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the RUN position.
PRIMER BULB
The PRIMER BULB removes air from thecar-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or marine oil. These oils will
cause engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554--6723.
FUELING ENGINE
WARNING: Remove fuel cap slowly
IMPORTANT
when refueling.
Experience indicates that alcohol blended fuels
(called gasohol or using ethanol or methanol)
can attract moisture which leads to separa-
tion and formation of acids during storage.
Acidic gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur. See the STORAGE sec-
tion for additional information.
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/WEED EATER brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
6
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
HELPFUL TIP
If your engine switch reads
“push to stop”, it is always
in the ON position.
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
HOW TO STOP YOUR UNIT
S To stop the engine, push andhold theSTOP
switch in the STOP position until the engine
stops.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8. Once the engine starts, allow it to run 10 se-
conds, then move the choke lever to the
RUN position. Allow the unit to run for 30
more seconds at RUN before releasing the
throttle trigger.
S If engine does not stop, move choke lever
to FULL CHOKE position.
HOW TO START YOUR UNIT
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1-800-554 -6723.
NOTE: If engine dies with the choke le-
ver in the RUN position, move the choke
lever to the HALF CHOKE position and
pull the rope until engine runs, but no
more than 6 pulls.
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
osition
STARTING A WARM ENGINE
1. Move the choke lever to the HALF
CHOKE position.
2. Squeeze and hold the throttle trigger.
Keep throttle trigger fully squeezed until
the engine runs smoothly.
3. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
4. Allow engine to run 15 seconds, then
move the choke lever to the RUN posi-
tion.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
Prim
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the RUN position; then, pull
the rope to clear the engine of excess fuel.
This could require pulling the starter handle
many times depending on how badly the unit
is flooded. If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554--6723.
hoke
ver
Starter Handle
7
advance properly and can cause serious
injury. Do not use other materials such as
wire, string, rope, etc. Wire can break off dur-
ing cutting and become a dangerous missile
that can cause serious injury.
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
ALWAYS WEAR:
Eye protection
CUTTING METHODS
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
whichcandamage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
S The tip of the line does the cutting. You will
achieve the best performance and
minimum line wear by not crowding the line
into the cutting area. The right and wrong
ways are shown below.
Long pants
Heavy shoes
Tip of line does
the
Line crowded into
w
Cut from your left to your right.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Right
Wrong
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
S The line will easily remove grass and
weeds fromaround walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
S During light duty cutting.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
S For mowing or sweeping, use full throttlefor
a good clean job.
TRIMMING -- Hold the bottom of the trimmer
head about 3 inches (8 cm) above the ground
and at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
To stop engine:
S Release the throttle trigger.
S Push and hold the STOP switch in the
STOP position until the engine stops.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
imming
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to andabove
the grassy area.
S Tap the bottom of the trimmer head lightly on
the ground one time. Approximately 2 inches
(5 cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy area.
Tapping on surfaces such as concrete or as-
phalt can cause excessive wear to the trimmer
head. If the line is worn down to 2 inches (5 cm)
or less, more than one tap will be required to ob-
tain the most efficient line length.
3 inches (8 cm)
above ground
SCALPING -- The scalping technique re-
moves unwanted vegetation. Hold the bottom
of the trimmer head about 3 inches (8 cm)
above the ground and at an angle. Allow the
tipof the linetostrike theground around trees,
posts, monuments, etc. This technique in-
creases line wear.
WARNING: Use only 0.080 inch (2
mm) diameter line. Other sizes of line will not
8
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
parallel to the ground. Avoid pressing the
head into the ground as this can scalp the
ground and damage the tool.
MAINTENANCE
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
INSPECT AND CLEAN UNIT AND DE-
HELPFUL TIP
CALS
IMPORTANT: Have all
repairs other than the rec-
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
ommended maintenance
described in the instruction
manual performed by an
S Wipe off unit with a clean dry cloth.
authorized service dealer.
CLEAN AIR FILTER
If any dealer other than an authorized
service dealer performs work on the
product, Electrolux Home Products,
Inc., may not pay for repairs under war-
ranty. It is your responsibility to maintain
and perform general maintenance.
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
1. Clean the air filter cover and the area
around it to keep dirt from falling into the
carburetor chamber when the cover is
opened.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
2. Open air filter cover by pushing button
(see illustration). Remove air filter.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
S Air Filter
S Housing Screws
S Assist Handle Screw
S Debris Shield
CHECK FOR DAMAGED OR
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Replace air filter and close cover.
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S STOP Switch -- Ensure STOP switch func-
tions properly by pushing and holding the
switch in the STOP position. Make sure en-
gine stops. Restart engine and continue.
9
As your unit is used, carbon deposits build up
on the muffler and spark arresting screen.
For normal homeowner use, however, the
muffler and spark arresting screen will not re-
quire any service. After 50 hours of use, we
recommend that your muffler be serviced or
replaced by your authorized service dealer.
Button
r
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch (0.6 mm). Igni-
tion timing is fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and
discard.
r
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
(19 mm) socket wrench.
MUFFLER AND SPARK ARREST-
ING SCREEN
4. Reinstall the spark plug boot.
WARNING: The muffler on this prod-
uct contains chemicals known to the State of
California to cause cancer.
SERVICE AND ADJUSTMENTS
7. With your finger between the lines, wrap
the lines evenly and firmly around the
spool in a clockwise direction.
REPLACING THE LINE
1. Press the tabs on the side of the trimmer
head and remove cover and spool.
8. Position the lines in the guide slots.
Cover
Tab
Guide Slot
uide
Slot
p Button
2. Remove any remaining line.
3. Clean dirt and debris from all parts. Re-
place spool if it is worn or damaged.
4. Replace with a pre-wound spool, or re-
place line using a 25 feet (8 meters)
length of 0.080 inch (2 mm) diameter
Poulan/WEED EATER brand line.
5. When installing new line on an existing
spool, hold the spool as shown in the il-
lustration below.
6. Bend the line at the midpoint and insert
the bend into the slot in the center rim of
the spool. Ensure line snaps into position
in the slot.
9. Insert the ends of the lines through exit
holes in the sides of the cover.
10. Place the spool in the cover.
Spool
Slot
Cover
11. Make sure the lines are not caught be-
tween the rim of the spool and the wall of
the cover.
12. Reinstall the spool and cover onto the
trimmer head. Push until cover snaps into
place.
Spool
REPLACING THE CUTTING HEAD
1. Align hole in the dust cup with the hole in
the side of the gearbox by rotating the
dust cup.
2. Insert a small screwdriver into aligned
holes. This will keep the shaft from turning
while removing and installing trimmer head.
10
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Idle Speed Adjustment
Screwdriv
Allow engine to idle. Adjust speed until engine
runs without stalling (idle speed too slow).
S Turn idle speed screw clockwise to increase
engine speed if engine stalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed.
3. While holding the screwdriver in position,
remove trimmer head by turning clock-
wise.
Idle Speed Screw
4. Thread replacement trimmer head onto
the shaft by turning counterclockwise.
Tighten until secure.
5. Remove the screwdriver.
CARBURETOR ADJUSTMENT
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during this procedure.
Wear your protective equipment and observe
all safety precautions.
Air Filter Cover
The carburetor has been carefully set at the
factory. Adjustments may benecessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is
released.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
If you require further assistanceor are unsure
about performing this procedure, contact an
authorized
service
dealer
or
call
1--800--554--6723.
STORAGE
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool before storing or trans-
HELPFUL TIP
porting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
S Store unit and fuel well out of the reach of
children.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
SEASONAL STORAGE
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy
storage.
S Clean air filter.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
OTHER
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
11
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plugbefore performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Carburetor requires
adjustment.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
smokes
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
1. See “Fueling Engine” in Operation
section.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
12
LIMITED WARRANTY
Poulan, a division of Husqvarna Outdoor Prod-
In Canada, contact:
ucts Inc., warrants to the original consumer pur-
chaser that each new Poulan brand gasoline
tool or attachment is free from defects in materi-
al and workmanship and agrees to repair or re-
place under this warranty any defective gaso-
line product or attachment as follows from the
original date of purchase.
Poulan
5855 Terry Fox Way
Mississauga,Ontario L5V3E4
Giving the model number, serial number and
date of purchase of your product and the name
and address of the authorized dealer from
whom it was purchased.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTH-
ER RIGHTS WHICH VARY FROM STATE TO
STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE LIM-
ITATIONS OR EXCLUSION MAY NOT APPLY
TO YOU.
This is a limited warranty within the meaning of
that term as defined in the Magnuson--Moss Act
of 1975.
The policy of Poulan is to continuously im-
prove its products. Therefore, Poulan re-
serves the right to change, modify, or discon-
tinue models, designs, specifications, and
accessories of all products at any time with-
out notice or obligation to any purchaser.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance or alteration, or
the use of accessories and/or attachments not
specifically recommended by Poulan for this
tool. This warranty does not cover tune--up,
spark plugs, filters, starter ropes, starter springs,
cutting line, or rotating head parts that will wear
and require replacement with reasonable use
during the warranty period. This warranty does
not cover pre--delivery setup or normal adjust-
ments explained in the instruction manual. This
warranty does not cover transportation costs.
In the event you have a claim under this warran-
ty, you must return the product to an authorized
service dealer.
Should you have any unanswered questions
concerning this warranty, please contact:
Poulan, a division of
Husqvarna Outdoor Products Inc.
1030 Stevens Creek Road
Augusta, GA 30907
1--800--554--6723
U.S. EPA/CALIFORNIA/ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U.S. Environmental
Protection Agency, California Air Resources
Board, Environment Canada and Poulan are
pleased to explain the emissions control system
warranty on your year 2007 and later small off--
road engine. In California, all small off--road en-
gines must be designed, built, and equipped to
meet the State’s stringent anti--smog stan-
dards. Poulan must warrant the emission
control system on your small off--road engine
for the periods of time listed below provided
there has been no abuse, neglect, or improp-
er maintenance of your small off--roadengine.
Your emission control system includes parts
such as the carburetor, the ignition system and
the fuel tank (California only). Where a warrant-
able condition exists, Poulan will repair your
small off--road engine at no cost to you. Ex-
penses covered under warranty include diag-
nosis, parts and labor. MANUFACTURER’S
WARRANTY COVERAGE: If any emissions
related part on your engine (as listed under
Emissions Control Warranty Parts List) is de-
fective or a defect in the materials or workman-
ship of the engine causes the failure of such an
emission related part, the part will be repaired or
replaced by Poulan. OWNER’S WARRANTY
RESPONSIBILITIES: As the small off--road
engine owner, youare responsiblefor the per-
formance of the required maintenance listed
in your instruction manual. Poulan recom-
mends that you retain all receipts covering
maintenance on your small off--road engine,
but Poulan cannot deny warranty solely for
the lack of receipts or for your failure to en-
sure the performance of all scheduled main-
tenance. As the small off--road engine owner,
you should be aware that Poulan may deny
you warranty coverage if your small off--road
engine or a part of it has failed due to abuse,
neglect, improper maintenance, unapproved
modifications, or the use of parts not made or
approved by the original equipment manufac-
turer. You are responsible for presenting your
small off--road engine to a Poulan authorized re-
13
pair center as soon as a problem exists. War-
ranty repairs should be completed in a reason-
able amount of time, not to exceed 30 days. If
you have any questions regarding your war-
ranty rights and responsibilities, you should
contact your nearest authorized service center
or call Poulan at 1--800--554--6723. WAR-
RANTY COMMENCEMENT DATE: The
warranty period begins on the date the small
off--road engine is purchased. LENGTH OF
COVERAGE: This warranty shall be for a pe-
riod of two years from the initial date of pur-
chase. WHAT IS COVERED: REPAIR OR
REPLACEMENT OF PARTS. Repair or re-
placement of any warranted part will be per-
formed at no charge to the owner at an ap-
proved Poulan servicing center. If you have
any questions regarding your warranty rights
and responsibilities, you should contact your
nearest authorized service center or call Pou-
lan at 1--800--554--6723. WARRANTY PE-
RIOD: Any warranted part which is not
scheduled for replacement as required main-
tenance, or which is scheduled only for regu-
lar inspection to the effect of “repair or replace
as necessary” shall be warranted for 2 years.
Any warranted part which is scheduled for re-
placement as required maintenance shall be
warranted for the period of time up to the first
scheduled replacement point for that part.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is de-
fective if the diagnostic work is performed at
an approved Poulan servicing center.
CONSEQUENTIAL DAMAGES: Poulan
may be liable for damages to other engine
components caused by the failure of a war-
ranted part still under warranty. WHAT IS
NOT COVERED: All failures caused by
abuse, neglect, or improper maintenance are
not covered. ADD -ON OR MODIFIED
PARTS: The use of add--on or modified parts
can be grounds for disallowing a warranty
claim. Poulan is not liable to cover failures of
warranted parts caused by the use of add--on or
modified parts. HOW TO FILE A CLAIM: If you
have any questions regarding your warranty
rights and responsibilities, you should contact
your nearest authorized service center or call
Poulan at 1--800--554--6723. WHERE TO GET
WARRANTY SERVICE: Warranty services or
repairs shall be provided at all Poulan service
centers. Call: 1--800--554--6723. MAINTE-
NANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any
Poulan approved replacement part used in
the performance of any warranty mainte-
nance or repair on emission related parts will
be provided without charge to the owner if the
part is under warranty. EMISSION CON-
TROL WARRANTY PARTS LIST: Carbure-
tor, Ignition System: Spark Plug (covered up
to maintenance schedule), Ignition Module,
Muffler including Catalyst, Fuel Tank (Califor-
nia only). MAINTENANCE STATEMENT:
The owner is responsible for the performance
of all required maintenance as defined in the
instruction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
14
|